JASO D – JAPANESE AUTOMOBILE STANDARD JAS0 D General rules of environmental testi. Buy JASO D Electrical Equipment – General Rules Of Environmental Testing Methods For Automotive Electronic Equipment from SAI Global. Find the most up-to-date version of JASO D at Engineering

Author: Faezuru Shaktitaxe
Country: Liechtenstein
Language: English (Spanish)
Genre: Sex
Published (Last): 27 March 2008
Pages: 49
PDF File Size: 8.78 Mb
ePub File Size: 6.64 Mb
ISBN: 318-9-41366-463-2
Downloads: 37389
Price: Free* [*Free Regsitration Required]
Uploader: Daramar

This test, jasoo, shall not be applied to the case of a chamber of O or C more. Some measurements are jwso, however, by inserting a fixed attenuator between the input terminal and the antenna, and some other measurements are done by using the roop antenna in place of dipole antenna when the accessory antenna of the measuring device is used and for the measurement of electric field around a vehicle body in VHF band, d01.

Upper portion of the instrument panel: Since under such condition, the generation o transient f voltage is limited to be kept so low that the test condition be made more relaxed, the resistance has been decided to be specified so to be directly connected with the power source and the test specimen.

Results of the study on electrostatic charged voltages of passenger car drivers r001 winter Fig. I btl Measureing instrument Loading Input device where, Low frequency oscillar: Main transient voltages on vehicles may be classified as follows: It is also expected that the voltage may rise near to the primary inductive voltage d0011 the time when the breaker is connected, according to the condition of arc discharge suppression. Output impedance 2 R or less, output 50W or grater Ammeter: Then take the test specimen out of the chamber, keep it for 2 hours or more under room temperature, test it according to 5.

Then, make the temperature gradually approached to other temperature and record in like manner.

JASO D 94 datasheet & applicatoin notes – Datasheet Archive

To measure the electric field strength by installing an EM1 meter or spectrum analyzer at the location of the test specimen: Any equipment installed under the spring of suspension system and any equipment installed on engine, the vibration of which is relatively high. Appearance and other conditions of the test equipment at that time shall also be confirmed.

Therefore, the time required of release was specified so as to be equal to 10 minutes to the maximum value as long after such maximum value on the condition at normal room temperature and under normal room humidity had been decked to be used.


However, voltages that are induced and impressed by transient voltages and electro-magnetic disturbances are not included.

The test specimen shall be operated under the test voltage having been applied thereto, after the operation of test specimen is stabilized, output of power source micro interruption equipment shall be micro interrupted and whether any abnormity exist or not of specimen shall be confirmed and recorded. A power supply switching device is fitted in the test circuit as shown by S1 in Fig. A study had been carried out so as to obtain allowable x001 of the testing voltage. Should it be essentially required, the frequency of voltage application are recommended to be increased in accordance with the agreement made between the persons concerned.

Raytac Module MDBT40/MDBT40-P Certified Automotive Standard JASO D001-94

Classification of tests The classification of tests shall be in accordance with Table. The method for natural drop to be alternatively employed was specified so as to be simply applied, where a little bit more severe condition than what is expected at usual handling was specified. Herein this paragraph, the matters in respect of general requirements and major points of revisions on this time are explained.

As for the measuring devices and methods, those which d0011 generally used for measurement of electric field strength are used. In addition, in respect of the allowable range of temperatures, it was unified so as to be equal to k 2 O as high in accordance with the C relating international standard, after the performance available from the existing constant temperature chamber in jas market having been investigated. Following two kinds of constant temperature chamber; 1 Low constand temperature chamber The inside temperature can be controlled so as to be kept at temperature within a range Of – 5 I 2 ” C.

Regarding above operations as one cycle refer to Fig.

Since it should be equal to “C as high a long the recent trend of the ISOs standards relating to automotive parts, this trend was introduced in the parts enclosed with so as to be able to be applied, should it be essentially required. Conducted electromagnetic tests are divided into two frequency bands of 30Hz to 50Hz and 50kHz to MHz, while the radiated electromagnetic tests are divided into three d010, test by magnetic field of 30Hz to 15kHz and tests by electric fields of 1MHz to MHz and MHz to MHz.


The test order of setting temperature is not particularly specified. Power source of charge on capacitor C Ei: However, supposed that those tests are required to examine the changed behavior of the equipment due to change of the environmental conditions only by temperature and humidity cycle test, it is not possible to uaso due to which the behavior available has been changed, either temperature change or humidity change. The classifications of the equipments shall be as follows: Accordingly, the revisions on this time were carried out mainly over the matters centered on a coordination with any other domestic and international rules relating thereto.

Some test results indicate, if a noise suppressor condenser is installed in parallel to the power supply circuit, it will constitute the major electrostatic capacity of the power supply circuit, and will affect on the generation of arc discharge.

Electronic c001 injection system, electronic ignition control system, etc. COQ 2R Maximum value of transient voltage: Of above mentioned transient voltages, test methods are specified in this standard for 1 through 5.

Confirm the appearance, etc. In respect of the time required of test, the 96 hours 4 days was decided to be designated as the condition representing them. JASO D possible. Specified values of resistor and capacitor shall be true value, not designated value. O to 30A, 30Hz to 15kHz Fig.


It was also decided that should it be essentially required to do so, the testing jawo testing time, cycling etc. TypeBandTypeE Of major transient voltages classified in the foregoing, these tests are based on the assumption of 3 and 4 above; that is to say, these 2, transient voltages of negative polarity, that generate when inductive loads connected to the vehicle electric circuit are cut off, are assumed.

Three points test voltages including both extreme values shall at least be performed, and more points are left to the agreement between the persons concerned.

Record the characteristics of the equipment accordingly. The class 3 carry out according to necessary condition. As was the case of A-1 and D-1, the test conditions the test circuit and the constants of its parts are specified based on the test results under the same operating conditions for alternator with A-1 and D-l.